• Roof Leak – Ten Most Common Roof Problems
Print Friendly, PDF & Email

Roof Leak – Ten Most Common Roof Problems

Roof One LLC, a Michigan Roof Contractor is ready to assist you with a FREE Roof Estimate, Storm Damage Analysis, and/or preventive maintenance inspection, at your request.

Free Damage Analysis

  • Icon 1.) Roof leaks and moisture
    • Roof leaks can occur for a number of reasons. Built-up roofs (BUR) might experience leaks due to flashing details that weren’t fastened properly during installation. 95 percent of leaks occur at flashing details – anywhere the membrane itself is terminated or interrupted. Additionally, hot bituminous and torch-applied modified bitumen roofs may experience leaks when a proper moisture barrier is not installed underneath a coping cap on parapet walls. Improper installation of flashing is a source of leaks on torch-applied modified bitumen roofs. Inadequate head laps and backwater laps are another mod bit installation problem that can allow moisture infiltration. Water can get under the membrane if the field of roof is installed so that water flows against the lap. The consequences of backwater laps are leaks and blisters, which can lead to roof failure. With cold-applied modified bitumens, improper storage of materials can result in moisture infiltration built into the roofing system, and under-application of adhesive can result in poor lamination and roof leaks. Leaks can result when single-ply membrane roofs are installed with poor seams. Good seams with single-ply membrane roofs is critical, if you don’t, you don’t have much. The membranes themselves hold water. Seams should either be glued or heat-welded properly.
  • Icon 2.) Blow-offs, tenting, reduced wind uplift resistance, and billowing
    • Leaks are not the only problem that can result from improperly installed flashing. Hot bituminous roofs where flashing is poorly attached may experience open seams and laps and ultimately cause blow-offs, reduced puncture resistance, and code issues. Poor gravel embedment and the use of an inadequate number of fasteners in the base sheet during application of both hot bituminous and torch-applied mod bit roof systems can also have similar consequences. Wind uplift resistance can be reduced greatly if seams are not cured adequately on cold-applied mod bit systems. Seams made with cold adhesives do not have good integrity until the adhesive has cured. If the seams are exposed to wind and rain before they are properly cured, moisture can infiltrate the roof system or wind uplift can damage the roof membrane. If not adhered properly to the substrate, single-ply roofs are at risk for blow-off and billowing.
  • Icon 3.) Poor installation and unsatisfactory workmanship
    • A faulty installation dramatically increases the likelihood of problems and reduces a roof system’s life expectancy. Workmanship does tend to be one of the more common problems or common reasons for problems that crop up at some point in the life of the Waukesha Wisconsin roof. BUR system installation can be problematic if specific preparations are not taken. Problems with adhesion can result when the area isn’t cleaned, dried, and primed properly prior to installation. These are things that are difficult to walk up on a roof and visually see, but could lead to future problems, premature aging, or premature failure. Torch-applied mod bit system performance can be compromised if crews do not relax the sheets prior to installation. Material preparation is important to a quality installation. Sheets installed that have not relaxed or are installed when ambient conditions such as temperature are not right can result in wrinkles, leaks, fish mouths, contraction of sheets, or blisters. Be sure your contractor and crew you’ve hired are educated in proper installation techniques specific to the roof they are installing.
  • Icon 4.) Lack of maintenance
    • There are many reasons not to neglect the roof – including financial and business continuity reasons. Being wise to problems can prevent their escalation. The problem in Wisconsin roofing is a lack of education on all levels. But if the owner of the property is better educated, the whole industry does better and less problems occur. Specific levels of maintenance are required to prevent voiding the warranty. Perform routine inspections. Look for ponding water, a piece of slipped base flashing, pitch pockets that haven’t been filled – those should be obvious whether you know a lot about roofing or not. Addressing minor problems before they escalate maximizes roof life as well as minimizes headaches and expense.
  • Icon 5.) Ponding water
    • A common problem across all roof types is ‘incidental ponding water.’ If we move the water off the roof, the roof has a really good chance of performing the way it should. During the design of a dead-level roof, slope should be added with tapered insulation or crickets. UV rays compounded by ponding water can have adverse effects on BUR and asphalt-based mod bit roofs. During installation of hot bituminous systems improper mopping can produce voids in the membrane, block drains, and result in ponding water as well as void the warranty. Before roof repairs are hastily made, the source of the ponding water should be investigated. HVAC units without condensate drain lines could be the culprit. Always inspect thoroughly before making a repair. Check drains to make sure they are free of dirt, silt, and debris.
  • Icon 6.) Punctures and the addition of penetrations post-installation
    • For all owners, but especially those with single-ply or spray polyurethane foam (SPF) roof systems, damage from foot traffic can be problematic. Punctures are something on high-traffic areas that can be a problem of single-ply systems. Add walkway paths or extra sacrificial layers of membrane. Abuse of the finished roof as one of the nine most common problems plaguing single-ply systems. Limit traffic and conduct cursory inspections after tradespeople have been on the roof. All roof systems’ performance is compromised when new equipment and penetrations are added to an existing roof, unless proper precautions are taken. When penetrations are added and deleted from a metal roof, the results can be disastrous. You are sometimes left with a compromise and a lot of caulking and sealants. Metal roofs move a lot. There is a lot of expansion and contraction, and if you are left to deal with caulking, you’re probably going to have problems eventually.
  • Icon 7.) Safety
    • The installation of hot bituminous and torch-applied mod bit systems requires strict adherence to safety procedures. Overheating asphalt can result in burns, and fires in the kettle and on the roof. In torch-applied mod bit applications, fire extinguishers should be present and MRCA CERTA program guidelines should be followed. During installation, odors from cold-applied mod bit systems can cause discomfort and alleged illness among building occupants. Outside air intakes should be covered in roofing areas.
  • Icon 8.) Improper repairs
    • Using materials that are not intended for application on specific roof types can result in permanent damage to the Wisconsin roof. One of the most common problems with metal roofs is improper repair. People go up with caulking and plastic roof cement and improper materials that are in no way intended for that purpose, making a small problem worse through that improper repair. Follow the manufacturer’s instructions for proper use and take note of repair products with a shelf life.
  • Icon 9.) Shrinkage
    • Single-ply roof types are each unique. The two most common things, especially on ballasted membranes, are pulling of the flashings (which is due to shrinkage of the field membrane) or deterioration – surface crazing and cracking of uncured membrane, commonly used at perimeter and penetration flashing.
  • Icon 10.) Blistering
    • Blistering, ridging, splitting, and surface erosion are symptomatic with BUR, and can eventually lead to bigger problems. While blisters are not always worth fixing, one of significant size should be addressed. Inadequate attachment of hot bituminous roof systems due to asphalt heated to an improper temperature can cause blistering, along with the slipping of felts, and accelerated aging. Bad interply integrity and dry laps can also result in the appearance of blisters.Ensuring a quality installation, providing the roof with consistent maintenance, and the early detection of problems through routine inspections can help maximize roof life. As the roof ages, the likelihood of problems increases. However, it is how these problems are addressed that will determine the fate and future of your roof system.
Request Free Estimate

Why Roof One?

We provide top notch service, use the best products on the market, and include the best installation warranties available. We offer affordable prices - sometimes as much as 30% less than our competitors!

Ready to get started?

Fill out our Free Estimate Request Form and send it to us today! We are ready to start your project!

Roof One Michigan

  • 275 Telegraph Rd.
  • Pontiac, MI 48341
  • Ph: 248-322-1000
  • RoofOne.com

Other Locations

  • Farmington/West Bloomfield: 248-848-8900
  • Flint/Grand Blanc: 810-835-4025
  • Rochester/Troy: 248-377-8978

Home | Estimate Request | Privacy Policy | Site Map | Contact Us

© Copyright 2017 Roof One LLC, Michigan. All Rights Reserved
Powered By Roofing Contractor Marketing